Guide · fishing
Homemade Light Rock Fishing Rods
After so many of your messages I decided to make a tutorial on how to build a light rock fishing rod in bamboo. If you are looking for a light rock fishing rod, why not try building one yourself? It is not difficult, you only need a little patience: I made mine in two afternoons, with the wind that on the first day made me stop recording, because to make a good rod you must not hurry and you have to give the right time to what you are doing. Here you will find everything I showed in the video, including the measurements.
Clicking loads the video from YouTube, which sets its own cookiesIn short. Two pieces of seasoned bamboo, cut and smoothed, joined by a joint bound with cotton thread. The handle is made with corks drilled with a drill, and the reel is held firm with two banded rings. I make the line guides from safety pins, tie them with black cotton thread and wood glue, the first 12 cm from the tip ring and then 2 cm more each time. Two coats of transparent varnish, a small reel with 0.18 or 0.20 mm line, and the rod is ready.
The light rock fishing rod: what you need
For light rock fishing, an ordinary spinning rod is not suitable. You need a much more sensitive and flexible rod, because these little predators, when they nibble our bait, if they feel a slightly stiff tip are not convinced: they leave, they flee. So a rod of about 2.20 m, quite flexible, but at the same time snappy at the moment of the strike. A small reel, a 1000 or a 2000, loaded with a good 0.18 or 0.20 mm line, and a 0.16 or 0.14 mm hooklength: these will never be big predators. The baits are small, soft plastics no longer than 2 inches, maximum 3, with very small jigheads. Everything must be proportionate, because light rock fishing is nothing more than light fishing among the rocks; but the English term is impressive, because if I had said “fishing with a rod on the rocks, but light” it would not have been the same thing.
In the Manual I wrote the measurements: rods from 1.80 to 2.20 m, light and sensitive, with a responsive tip to feel the bites without scaring the fish. In the bamboo version, thinner pieces are used than for spinning rods, with an extremely sensitive but responsive tip, and more guides, usually seven or eight, for a more parabolic curve in casting and retrieving.
Where to fish with this rod
Wherever there are rocks: from harbor piers, from beaches with scattered rocks, but above all from rocky shores, and the ideal rocks are those colonized by seaweed, with crabs, hermit crabs, shrimps and sea urchins: there is the food chain, and from the bottom to the surface you will find gobies, scorpionfish, wrasses, ornate wrasses, saddled seabream and even small groupers. Where, when and how to fish, with soft plastics and bread, is in the guide how to go light rock fishing.
What you need to build the rod
- Two pieces of seasoned and straightened bamboo, a thicker one for the butt and a thinner one for the tip; how to collect and season bamboo is in the guide to the DIY bamboo fishing rod;
- A little piece of bamboo or giant cane for the joint;
- Corks, sparkling wine corks are fine;
- Two banded rings to hold the reel firm;
- Safety pins for the line guides, and a thin little tube for the tip ring;
- Strong cotton thread for the joint and black cotton thread for the bindings;
- Wood glue and a small brush;
- Clear glossy varnish, plus a color of your choice;
- A drill with bits, a small hacksaw and sandpaper.
How I build it, step by step
1. Cut the two pieces and smooth them
Cut the two pieces to the size you have decided and smooth them with sandpaper. I left the nodes, to show the bamboo in its original state.
2. The cork handle
I take simple sparkling wine corks, drill them with a bit as wide as the rod and insert them at the bottom of the butt: one cork, then the space for the reel, then another piece of cork on top. In the Manual I glue them with wood glue and smooth them with sandpaper.

3. The reel attachment
On the handle I inserted two simple banded rings: they are used to fix the reel to the handle, one for each foot. There is no need for a store-bought reel seat.
4. The joint
At the top of the first piece I put a bamboo joint; if you do not want to make it in bamboo, a simple reed from the thicket, the common giant cane, is fine. I glued it and then tied it with some strong cotton thread, at the bottom and at the top: the binding prevents the rod from breaking during strong actions. In the Manual the joint is made by binding the first ten centimeters of the piece in tight turns, with glue on top and twenty-four hours of drying, and then widening the hole with a drill bit of the same thickness as the piece to be inserted.

5. The guides from safety pins
I made the line guides myself with safety pins. Take a safety pin, open it, insert the drill bit to get the right size of the ring, then straighten the stems, cut them to size and shape them a little more: you get a little ring with two little feet to bind. I made the tip ring with a little piece of thin tube taken from a broken radio antenna, with the bent pin inside. In fishing shops you can find much better series of rings, but I am showing you a very simple way to make them at home.
6. The distances
How many little rings do you need on a 2.20 m rod, and at what distance? I put the first little ring 12 cm from the tip ring and make a mark. From the first to the second I leave 14 cm, then 16, then 18, then 20: each ring 2 centimeters more than the previous one, up to the largest ring, the one near the reel. In the Manual, for light rock fishing rods, I recommend seven or eight rings.
7. The binding
I take some black cotton thread and pass it around the foot of the ring, turn after turn: it is a job of patience. Then, with the little brush, I spread wood glue over it. I recommend fitting the tip ring first: this way all the others will be aligned in the same direction. Tie the second one, check that it is in line with the first, and so on; then let it dry.
8. The color and the varnish
At this point you personalize it: everyone makes it with the colors they like, like their own home. I colored the joint red, wrote “light rock fishing” on the handle and gave two coats of clear glossy varnish, which besides making the rod shine makes it waterproof.
The reel and the line
For light rock fishing you need a very small reel, loaded with 0.18 or 0.20 mm line. Look at it with all the rings made from safety pins, all in line: not bad at all.
Building rods, guys, is always great fun: we choose the right size according to the spot where we want to fish, and then we enjoy ourselves, both building the tackle and fishing with it. With my little bamboo rods I have caught groupers, scorpionfish, saddled seabream and many little inhabitants of the rocky shore: you can see it in the pages light rock fishing with bread and fishing for groupers.
Frequently asked questions
How long should a light rock fishing rod be?
About 2.20 m: in the Manual I indicate from 1.80 to 2.20 m. Flexible and sensitive, but snappy at the strike.
What reel and line do you fit?
A small reel, 1000 or 2000, loaded with 0.18 or 0.20 mm line, and a 0.16 or 0.14 mm hooklength.
How do you make the guides without buying them?
With safety pins: open them, take the measurement with the drill bit, straighten the stems, cut them and shape them. The tip ring with a thin little tube and a pin.
At what distance do the guides go?
The first 12 cm from the tip ring, then 14, 16, 18, 20: 2 centimeters more each time, up to the largest ring. In the Manual I recommend seven or eight rings in total.
Keep reading
Light rock fishing rods are born from the bamboo spinning rod, which has its own guide: bamboo spinning rods. In the DIY Fishing Manual there are all the rods with my drawings, and on the site all the DIY fishing and light rock fishing.
Believe me, fishing with homemade bamboo fishing rods makes fishing even more magical!
Tight lines, guys!
